Ghost Controls Hinge & Roller Replacement Nationwide

Ghost Controls Hinge & Roller Replacement: The Tarzana Owner’s Guide

We stock and install Ghost Controls-compatible hinge and roller replacements for Tarzana homeowners, with most swaps running between $185 and $420 installed depending on the hinge configuration and how much of the roller assembly has worn. Same-day service is available when the part is on our truck, which it usually is for the common Ghost Controls slide and swing models.

Call (424) 258-8818

The way most Tarzana owners discover this part has failed is not dramatic. The gate starts dragging, or it makes a sound like a shopping cart with a flat wheel, or it hangs a quarter inch low on the latch side. By the time it’s visible, the roller usually has a flat spot and the hinge pin has been carrying weight it was never meant to carry alone.

If that sounds like your gate this week, you want the part matched, priced in writing, and installed without a second visit. That’s the page you’re on.

Which Ghost Controls Models This Applies To

Ghost Controls builds automation kits for two gate types: sliding gates and single or dual swing gates. The hinge and roller hardware we replace falls into three groups.

For the Ghost Controls slide gate kits (AXDP, AXXP, and the DTP series), the rollers are steel or nylon wheel assemblies that carry the gate along a ground track. These are sold as paired sets, and Ghost Controls specs them by wheel diameter, usually 2 or 3 inches, and by the bracket bolt spacing. The compatibility gotcha we see in Tarzana: a 3-inch roller will not fit in a bracket cut for a 2-inch wheel, even though the bolt pattern looks close at a glance. Measure the wheel, not the bracket.

For swing gate kits (SXP1, SXP2, and the older R series), the hinges are post-mount or weld-on plates with greaseable pins. Ghost Controls does not manufacture its own hinges; the kits ship with generic heavy-duty hinges sized to the gate weight. That means a quality aftermarket hinge is entirely appropriate here, as long as the bolt pattern and the pin diameter match. We stock both the OEM-spec sizes and a heavier aftermarket option for Tarzana gates that catch afternoon wind off the Santa Monica Mountains.

For roller guides on swing gates, the small caster wheel that supports the free-swinging leaf at mid-travel is the part that fails first. It takes a beating on uneven Tarzana driveways, and when it fails, the leaf drops and the opener starts tripping its obstruction sensor.

Signs Your Ghost Controls Hinge & Roller Replacement Is Failing

• The gate sags visibly on the latch side. This means the hinge pin or the hinge plate has worn to the point where the gate leaf is no longer held square. On a Ghost Controls swing gate, the operator then fights gravity on every cycle, which shortens the motor life.
• A grinding or squealing sound during travel that was not there when the gate was installed. Flat spots on slide gate rollers make a rhythmic thump-and-grind as the gate moves. Tarzana’s dry season accelerates this because worn rollers pick up grit from the track and act like sandpaper.
• The gate shudders or jerks mid-travel. This is usually not the motor. It is a worn roller binding against the track, or a hinge pin that has developed play. The motor is just the symptom.
• Higher energy draw from the opener, or the opener tripping its force setting. Worn hardware makes the motor work harder. If Ghost Controls technical support tells you the amp draw is climbing, the hinge or roller is the usual culprit before the board or the motor itself.
• The gate now scrapes the driveway or the bottom guide rail. On slide gates, this is a collapsed nylon wheel. On swing gates, it is a hinge that has shifted. Either way, continued cycling will score the driveway and eventually damage the gate frame.

Before

After

Replacement Cost & What’s Included

For Tarzana homeowners, here is the pricing we quote in writing before any work starts:

• Hinge replacement (swing gate, single leaf): $185-$310 installed, depending on the hinge weight class and whether the post side needs a new plate.
• Hinge replacement (swing gate, dual leaf): $340-$560 installed when both leaves show wear and we replace all four hinge points.
• Roller replacement (slide gate, pair): $190-$420 installed, varying by wheel diameter, material (nylon vs steel), and whether the brackets are reusable.
• Support caster / guide roller replacement (swing gate): $95-$150 installed.

These figures cover the part, the labor, and the documentation. Every Ghost Controls hinge and roller job in Tarzana gets a written price before we touch anything, under Haven Standard Clause 1, and a photographed record of the old part, the new part, and the final alignment before we leave. No surprise invoice at the end.

All hardware we install carries a 365-day parts and labor warranty through the Done Right Promise. If it fails within that year, we make it right at no additional charge.

DIY or Call Us?

For slide gate rollers, an owner with basic tools can replace a wheel assembly in under an hour. The roller bolts to the gate frame through a bracket, and the gate does not need to be fully removed, only supported. What usually goes wrong is the alignment: if the two rollers are not set at the same height, the gate will crab and chew through the new wheel in months. That is the part worth a trained eye.

For swing gate hinges, especially on a heavy gate, we say call. The gate leaf has to be solidly supported before the old hinge comes off, and a gate that falls on someone is a serious injury. We use mechanical frames and take the weight off the hinge before any bolt comes loose.

If you want to replace the part yourself and just need the correct Ghost Controls-compatible roller or hinge matched to your model, call us and we will tell you the exact spec and sell you the part. If you would rather we handle it end to end, that is what we do every week in Tarzana. Call (424) 258-8818 and we will have a technician there with the part on the truck.

FAQs