Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Burbank, CA
Gate access control in Burbank means working around two very different demands: studio and production-facility gates running thousands of cycles a week on Olive Avenue and Pass Avenue, and 1940s-1960s ranch homes in the residential flats where old ornamental iron gates need upgraded keypads, phone entry, or card readers. The heat is the constant variable. Burbank summers regularly push past 105°F, and that thermal load degrades access-control circuit boards faster than coastal neighborhoods see. Call (424) 258-8818 and a live person answers, any hour.
Why Burbank Homes Are Different
Burbank’s residential core is mostly post-WWII ranch homes and bungalows built between the 1940s and 1960s. Many of those properties still carry their original tubular steel or ornamental wrought-iron driveway gates. A gate that has stood since the Eisenhower administration has usually settled: footings shift, posts lean, hinges wear oval, and operators that were retrofitted in the 1990s are now failing year after year. The Rancho neighborhood’s larger lots tend to have heavier double-swing gates, which stress older hinges and posts disproportionately.
The climate compounds all of it. Burbank sits deep in the San Fernando Valley and records some of the highest temperatures in the Los Angeles Basin. That heat warps wood gate panels, accelerates grease breakdown inside gear-driven operators, and shortens the life of circuit boards mounted inside metal operator housings that bake in direct sun. Seasonal Santa Ana winds put lateral load on tall swing and slide gates, bending tracks and snapping bottom rollers on gates that were not designed for sustained wind.
Then there’s the studio factor. Warner Bros., Disney, and numerous production facilities operate commercial gates that run thousands of open-close cycles per week. Parts selection that is fine for a residential driveway fails quickly on a studio-adjacent gate. We apply that lesson in the other direction too: when a Burbank homeowner replaces an operator, we size components for heat and cycle count, not just the gate’s weight.
Our Main Burbank Services
Burbank homeowners and property managers call us most often for three things: repairing a gate that has stopped opening, installing a new gate on a settled or sloped driveway, and replacing or servicing the motor and opener that drives it. Each has its own dedicated Burbank page linked below.
Gate Repair in Burbank
Most repair calls in Burbank involve a gate that will not open, a gate that reverses mid-travel, or a hinge that has torn loose from an aging post. Our Gate Repair in Burbank page covers the full scope: on-site troubleshooting, written pricing, and the 365-Day Done Right Promise on every completed repair.
Gate Installation in Burbank
New installations in Burbank usually start with the existing driveway and posts. Ranch homes on the flats often need footings re-poured before a new gate can be hung square; Rancho properties with double-swing gates need post reinforcement before a heavier gate goes up. See Gate Installation in Burbank for what a full install includes and what it costs here.
Gate Motor & Opener in Burbank
Burbank heat kills operator circuit boards and bakes grease out of gear drives. When a motor fails, the repair usually means either a board replacement, a gear-train service, or a full operator swap on a newer arm bracket. The Gate Motor & Opener in Burbank page breaks down install and repair pricing for the brands we service.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Burbank
Gate access control in Burbank means adding or repairing the layer that decides who gets through: keypads, phone entry, card readers, or video intercoms mounted at the driveway. In the studio-adjacent commercial corridors, access control runs heavy hours in direct heat; in the residential neighborhoods around Rancho and Magnolia Park, homeowners want systems that survive a valley summer and let them buzz in a delivery from the house. Our Gate Access Control work is quoted in writing before anyone touches a wire, and the finished job includes a photographed record of every connection and setting.
Keypad Entry
Signs you need it
The keypad works only in mild weather, or some keys stopped responding after a hot spell.
What it costs in Burbank
A standard gate keypad replacement in Burbank runs about $150-$450, depending on the model and whether the wire run is intact.
How we do it
We pull the old keypad, check the conductor path for heat damage, mount the new unit, program the codes, and photograph the completed wiring.
Phone Entry
Signs you need it
The call box either will not dial out or callers report that the audio cuts in and out during the day’s hottest hours.
What it costs in Burbank
A phone-entry upgrade in Burbank typically lands between $200 and $650 installed, depending on whether it’s a cellular or landline bridge.
How we do it
We test the existing phone line or switch to a cellular unit, replace the call station, pair it with the operator, and leave a written record of the configuration.
What Gate Access Control Costs in Burbank
| Item | Typical range in Burbank |
|---|---|
| Keypad replacement | $150-$450 |
| Phone entry upgrade | $200-$650 |
| Card reader / keypad combo install | $300-$850 |
Can you integrate access control with an older operator?
Yes. Most access-control devices wire into the operator’s existing input terminals, so the operator’s age rarely matters. We verify the circuit path on site and document the connection. Call (424) 258-8818 if your operator predates the keypad you’re planning.
Does Burbank require a permit for an access-control upgrade?
Most residential keypad, phone-entry, and reader swaps do not require a permit because no structural work is involved. If the install includes a new post or conduit trench, the contractor pulls permits as part of the written scope. We confirm this in the quote before starting.
Gate Parts & Welding in Burbank
Gate parts and welding in Burbank is where older gates come back to life. The 1940s-1960s ranch stock is full of ornamental iron gates with rusting stiles, torn hinges, and posts that have settled out of square; the heat warps panels and the Santa Ana winds finish the job on the hardware. Our Gate Parts & Welding service replaces or repairs those components in place, with a written record of every part number and a photo log of the weld before and after.
Hinge Replacement
Signs you need it
The gate sags at the latch side and scrapes the driveway when it swings.
What it costs in Burbank
A hinge replacement on a Burbank driveway gate typically costs $120-$350 depending on the hinge size and whether the post-side plate needs welding.
How we do it
We support the gate, remove the worn hinge, inspect the post for cracks, weld or bolt a new hinge, and photograph the final alignment.
Post Reinforcement
Signs you need it
The post leans or the gate sags even after hinges are replaced, which usually means the footing is compromised.
What it costs in Burbank
Reinforcing or replacing a settled gate post in Burbank usually $250-$600 including the new concrete footing and re-setting the gate.
How we do it
We cut and remove the old post if required, pour a new footing, set a new or reinforced post, re-hang the gate, and document the alignment.
What Gate Parts & Welding Costs in Burbank
| Item | Typical range in Burbank |
|---|---|
| Hinge replacement | $120-$350 |
| Post reinforcement | $250-$600 |
| Custom welding repair | $80-$200 per weld (varies by material and position) |
Can you weld a gate track in place on an incline?
Yes. We repair or replace gate tracks on sloped Burbank driveways, including re-shimming to correct the pitch. The repair is photographed and the new track position is recorded on the write-up.
Will the weld match the original gate finish?
Structurally, yes. Cosmetically, the weld area is ground smooth and primed; repainting and finishing is the homeowner’s part unless arranged in the written scope. We can match the finish on request, and the price is quoted before work starts.
Brands We Service in Burbank
We service and install DoorKing, Elite, Mighty Mule, and LiftMaster among others, and we keep common control boards, photo-eyes, and arms in the truck for Burbank calls. One visit usually means a same-day fix, not a parts-order delay. See our brands for the full list.
Pricing for Gate Repair in Burbank, CA
| Service | Typical range in Burbank |
|---|---|
| Gate troubleshooting / diagnosis | $85-$165 |
| Photo-eye alignment / replacement | $65-$150 |
| Limit switch reset / replacement | $75-$180 |
| Circuit board replacement | $120-$350 |
| Opener arm / bracket repair | $90-$240 |
| Keypad replacement | $150-$450 |
| Phone entry upgrade | $200-$650 |
| Hinge replacement | $120-$350 |
| Post reinforcement | $250-$600 |
| Full operator replacement | $650-$1,600 |
Prices in Burbank push toward the high end when a gate is a studio-adjacent commercial unit cycling thousands of times a week, or when a 1950s post needs a new footing before any repair can hold. Every job is quoted in writing before work begins, and the price that is quoted is the price that is invoiced.
Neighborhoods We Serve in Burbank
We route crews across Burbank daily and respond to urgent gate failures throughout the city, including:
- Rancho
- Magnolia Park
- Verdugo Hills
- North Burbank
- Media District
Most Burbank service calls are reached within two hours; access-control and welding jobs are quoted in writing at the visit.
Service Area - Cities Near Burbank
We cover Burbank and the surrounding communities in the San Fernando Valley. If your gate is just over the line, see North Hollywood, CA, Studio City, CA, Van Nuys, CA, or West Hollywood, CA.
Serving Burbank, CA - Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Burbank
We dispatch Burbank service calls throughout the day, and a live person answers the phone any hour at (424) 258-8818. Emergency gate failures are usually reached within two hours, depending on the time of day and where the gate is located in the city.
Repairs and parts replacement do not typically need a permit. New gate installations, new footings, or replacing a post in Burbank may require one, and we include permit handling in the written quote when the scope calls for it. Final permit requirements come from the city.
Yes. We repair common-entry and driveway gates for Burbank HOAs and small complexes, including phone entry, card readers, and swing or slide operators. The work is documented in writing, and we keep the HOA’s maintenance file current on every visit.
If your Burbank gate is down or the access control stopped responding, call (424) 258-8818. A live person answers, and we’ll give you a written price before any work starts.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Burbank Customers Say
"Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N.