Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Installation in Tarzana: What to Know First
FAAC gate installation in Tarzana starts with a written price before any tool comes off the truck. We install, replace, and retrofit FAAC gate operators across Tarzana, typically completing most residential swing and slide gate installations in one day once the operator and brackets are on hand. A complete FAAC swing gate operator install in Tarzana usually runs between $1,450 and $2,900 depending on the series, gate weight, and whether we’re reusing existing brackets or fabricating new ones. If you already own a FAAC unit or need one spec’d for your driveway, call (424) 258-8818 and a live person answers, any hour.
How FAAC Products Fail - and How We Fix Them
- FAAC 400 Series (swing): limit switch drift after heavy wind events. Tarzana gets gusty afternoons off the Santa Monica range, and we routinely find FAAC 400 operators where the wind forced the gate leaf past its mechanical stop enough to knock the internal limit cam out of registration. The symptom is a gate that opens fine but then slams against the closed stop or reverses immediately. Our fix is resetting the limit to the physical travel point and photographing the new position, because a gate that fights its stops burns through the operator’s gearbox faster than almost anything else we see.
- FAAC 750 and 844 series (slide): capacitor failure on undersized power runs. Tarzana homes built in the 1960s and 1970s often have the original conduit to the gate, and that wire gauge was never meant to carry a modern slide operator. We see FAAC slide units where the start capacitor fails within two or three years because the voltage drop across a long, undersized run forces the cap to work harder on every open cycle. Before installing a replacement capacitor, we meter the line with the gate under load and document the reading. If the run can’t support the motor, the written quote includes the new conductor run as a line item, not a surprise.
- FAAC E124 (residential swing): sheared bolt at the crank arm attachment. This is a repeat call in Tarzana, specifically on solid wood or heavy ornamental gates where the leaf weight was never properly balanced. The E124’s crank arm bolts to the gate bracket, and when the gate is too heavy or the hinges are sagging, the shear point is always the attachment bolt. We don’t just replace the bolt; we check the hinge alignment and gate weight, and if the load exceeds the E124’s rating, we say so in writing and offer options rather than installing a motor that will fail the same way in eighteen months.
- FAAC control board corrosion from coastal-adjacent air and irrigation overspray. Tarzana sits far enough from the coast that no one expects corrosion, but we’re close enough that microclimates and wildly over-sprayed lawn irrigation are the real culprits. FAAC boards are reliable, but when a board sits in a housing with no weather gasket or a cracked lid, the terminal strip oxidizes and you get intermittent open commands or a gate that moves two inches and stops. We replace terminated ends, seal the housing, and photograph the before and after so you can see exactly what was corroded and what was replaced.
- FAAC S800H (hydraulic swing): low hydraulic fluid from a slow weep at the release fitting. This is a quiet problem. The operator still runs, but the gate moves slower each month and the motor draws more current. The symptom an owner notices first is a hum that gets louder, or the gate hesitating halfway through its travel. We check fluid level and leak points on every FAAC service call, and the fix is usually a new O-ring, a top-off, and a test cycle under load. Hydraulic FAAC units are less common in Tarzana than the electromechanical ones, but when we find them they’re almost always on older custom estate gates along the quieter streets north of Ventura Boulevard.
Our FAAC Gate Installation Process
- 1
The call. You reach a live person at (424) 258-8818. We ask what the gate is doing, what FAAC model you have, and whether the operator is currently working at all. We schedule the visit, usually same day or next morning for a dead gate.
- 2
The inspection. Adrian Vance or one of our uniformed techs arrives, checks the gate weight, hinge health, operator mounting point, and existing wiring. Every reading gets written down: voltage at the board, current draw under load, gap between the photo-eye beam and the gate path.
- 3
The written scope. Before any work starts, you get a flat written price covering exactly what we’ll do. That includes the part number for the FAAC operator we’re installing or the components we’re replacing, the labor, and any additional materials like brackets, conduit, or safety edges.
- 4
The install. We mount and wire the FAAC unit, configure travel limits, set force sensitivity so the gate reverses rather than pushes through an obstruction, and align every safety device. If the job needs a new power run, we explain the conductor size and why before pulling a foot of wire.
- 5
The test and the record. We run the gate through 20 to 30 open and close cycles under different load conditions, check for overheating at the motor housing, and confirm the auto-close timer and manual release function correctly. Before we leave, you get a photo log of the installation and a written record of every part number installed. That’s Haven Standard Clause 4: evidence on every job.
BeforeAfterWhat FAAC Gate Installation Costs in Tarzana
FAAC gate installation in Tarzana varies more by setup than by brand. A straight replacement of an existing FAAC swing operator, reusing the current brackets and wiring, typically runs $1,450 to $2,200. A full slide gate installation with new mounting plate, rack, and safety edges lands between $2,300 and $3,600. What moves the price: gate weight and balance, whether the existing conduit can carry the motor’s draw, how much fabrication the mounting points need, and whether we’re adding photo-eyes or a keypad. Every quote is written and delivered before work starts, not after. Call (424) 258-8818 for an exact price on your gate, free estimates included.
Why Tarzana Homeowners Call Vance Gate Repair Tarzana for FAAC Work
Most of our FAAC jobs in Tarzana come from a previous repair where we documented what we found and the homeowner kept the record. That’s the whole point. We price FAAC work in writing, up front, under Haven Standard Clause 1, and that written price is the price - no surprise invoice at the end. If the install isn’t right within 365 days, we make it right at no charge under our 365-Day Done Right Promise. We’re independent FAAC service providers, not an authorized dealer, which means we spec what’s best for the gate, not what a brand agreement tells us to push. And when a property has a mix of brands - a LiftMaster on the driveway, a Ghost Controls on the pedestrian gate, a Mighty Mule on the side yard - we can service all of it in one trip. One company, nine brands, one written record. Name what you found, name what it costs, name what you left behind.
FAQs
If the operator is installed by an independent provider like us and the installation follows the manufacturer’s published specifications, the FAAC product warranty generally remains intact on the hardware itself. What we preserve carefully is your installation record: we photograph the mounting, the wiring terminations, the limit settings, and the safety device alignment so if a warranty claim ever comes up, you have documentation of a correct install.
Most residential gates in Tarzana can take a FAAC swing or slide operator, assuming the gate is structurally sound, properly hinged, and within the motor’s weight and cycle ratings. We check all three before quoting. If a gate is too heavy for the FAAC model you own, we tell you in writing and explain the options rather than installing it and letting the gearbox eat itself in a year.
We keep the most common FAAC components in stock - control boards for the 400 and E124 series, capacitors, limit switches, and release assemblies - because those are what fail most often in Tarzana. For less common parts, most arrive within two to five business days. We’ll tell you which situation applies before we start, and the written quote reflects the parts lead time.
For a straightforward replacement of an existing FAAC operator, we can often complete the install the same day we arrive. New installations with additional wiring, fabrication, or safety-edge work usually take one to two days. The schedule depends on what the inspection turns up, not on a promise we make before seeing the gate.
We look at the same three things every time: the age of the unit, the cost of the failed component, and whether the operator is properly sized for the gate it’s moving. If you have a FAAC 400 that’s fifteen years old and the board and the gearbox both need replacing, a new unit usually makes more financial sense. If it’s a five-year-old E124 with a sheared attachment bolt, repairing is the right call. We’ll show you the numbers for both and let you decide from a written quote.
Ready to Get Your FAAC Gate Installed in Tarzana?
Call (424) 258-8818 and tell us what your gate is doing, or not doing. You’ll get a live person, a straight answer, and a written price before any work starts. That’s how Vance Gate Repair Tarzana has handled every FAAC installation since 2014, and it’s how we’ll handle yours.
Written by Adrian Vance, Owner, Vance Gate Repair Tarzana at Vance Gate Repair Tarzana, serving Tarzana and nearby areas.