Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Parts & Welding for Tarzana Homeowners
Gate parts and welding in Tarzana covers the structural repairs that keep a driveway gate square, quiet, and latched: hinge replacement, post resetting, rail repair, custom steel fabrication, roller swaps, and latch work. Most of these jobs run between $180 and $650 in this area, and we carry the steel, hinges, rollers, and welding equipment on the truck to finish most calls the same day. Vance Gate Repair has handled gate parts and welding since 2014, and every job starts with a written price before any tool touches metal. Call (424) 258-8818 and a live person answers, day or night.
What sets us apart in Gate Parts & Welding - Tarzana is the documentation. Under Haven Standard Clause 4, every visit leaves you a photo record of what was found, what was welded or replaced, and the part numbers installed. No gate parts job leaves the property without evidence. That’s the habit Adrian Vance built in commercial access-control work starting in 2014, and it’s the same standard applied to every residential gate we touch.
What Our Gate Parts & Welding Service Includes
Hinge Replacement
Gate hinges carry the entire weight of the gate leaf, and when they sag, the latch stops lining up and the motor strains against misalignment. In Tarzana we see this most often on older wrought-iron gates where the barrel has worn oval from years of dry operation. We cut off the failed hinge, grind the post clean, weld a new barrel hinge in position, and photograph the finished weld before we leave.
Post Replacement
A leaning post is almost never a hinge problem. The post has rusted at ground level or the concrete footing has cracked, and the entire weight of the gate is now leaning on the motor’s arm bracket. We remove the old post, core the footing, set a new steel post in concrete, and let it cure properly before re-hanging the gate. You get photos of the footing depth, the post plumb line, and the final weld.
Rail Repair
On slide and cantilever gates, the rail is the track the gate rides on, and a bent rail makes the gate grind, jump, or stall. We cut out the damaged section, weld in new steel, and grind the weld smooth so the rollers pass without resistance. If the rail has snapped, we reinforce the repair with a sleeve plate rather than just surface-welding the crack.
Custom Welding
Not every gate repair comes from a catalog. When a hinge point has torn out of a decorative gate panel, or a diagonal brace has cracked, the right repair is a custom-welded reinforcement plate cut to fit the exact geometry. We weld in place on-site with portable MIG equipment, dress the weld to match the surrounding metal, and prime it. The photo record includes a close-up of the weld bead so you can see exactly what was done.
Gate Rollers
Slide gates ride on steel rollers, and when a roller bearing fails, the gate drags and the motor pulls excessive amperage. We replace worn rollers with new sealed-bearing units, adjust the height so the gate travels level, and lubricate the track. On most Tarzana slide gates - and with our Gate Parts & Welding in Reseda - roller replacement takes under two hours and the improvement is immediate: the gate moves with one hand.
Latch & Lock
A gate that won’t latch is a gate that bangs in the wind and binds against the lock plate. We replace the latch, align the strike plate, and adjust the release mechanism so the gate closes firmly and locks without slamming. If the lock has corroded internally from Tarzana’s heat and occasional salt air drift, we replace it rather than soak it in oil and call it fixed.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Parts & Welding
LiftMaster gate operators are common throughout Tarzana, and we’ve welded more than a few broken LiftMaster arm brackets back onto posts where the original weld failed. We keep the OEM hardware on the truck and we know the bolt patterns and bracket geometry by heart.
DoorKing slide and swing operators are built around steel frames that occasionally crack at stress points. We’ve repaired and reinforced DoorKing gates across the San Fernando Valley, and we document every weld with the operator model number in the record.
We also service Elite and Mighty Mule installations, and the parts work is the same discipline regardless of brand: cut out the failed metal, weld in sound steel, dress and prime the repair, and photograph it. Whether you have one of those brands or any other make, we can get the parts and the weld done. The home page has more detail on our full service approach.
BeforeAfterSigns You Need Gate Parts & Welding Right Now
- The gate sags and scrapes the driveway. This means a hinge or the post itself has failed. The motor keeps pushing, the latch keeps misaligning, and the scrape only gets deeper. A sagging gate will eventually tear the motor bracket off the post.
- The gate jumps or shudders when moving. A bent rail or a dead roller bearing causes that stutter. The motor is working against mechanical resistance, and that resistance becomes a burned-out control board if it runs long enough.
- The latch won’t stay closed. A gate that won’t latch is a gate that swings free in wind and bangs against its stop. The fix is usually latch replacement and strike alignment, but if the post has shifted, the post gets reset first.
- You see rust flakes at the post base. That’s structural rust, not surface rust. The post is losing wall thickness where it matters most: right at the concrete line. A gate that leans is days or weeks away from snapping.
- A weld has cracked and the metal is opening up. Cracks propagate. What starts as a hairline crack becomes a sheared bracket, a dropped gate leaf, and a serious safety hazard. A cracked weld is a call-today item.
Our Gate Parts & Welding Process - Step by Step
- 1
Written estimate on arrival. The technician inspects the gate, measures the wear on hinges, posts, and rollers, and writes a flat price on paper. That price is signed before any cutting or welding begins. Haven Standard Clause 1: have it in writing.
- 2
Diagnostic photos before disassembly. We photograph the failed parts in place: the cracked weld, the bent rail, the sagged hinge. That record goes into your job file and yours to keep.
- 3
The repair work. We cut, weld, reset, and replace using the correct steel and components for the job. No shortcuts on a gate that weighs 400 pounds and moves on a motor.
- 4
Function test and adjustment. After the weld cools and the hardware is torqued, we cycle the gate through full travel, check the latch engagement, and verify the motor is not over-amping against the repaired rail or hinge.
- 5
Photo record and written closeout. Before we leave, you get the photo log of every adjustment and a written record of every part number installed. Clause 4: evidence on every job. The 365-Day Done Right Promise covers the completed work for a full year.
How Much Does Gate Parts & Welding Cost in Tarzana?
Gate parts and welding prices in Tarzana depend on what failed and how much metal we’re replacing - see how much Gate Parts & Welding costs for typical ranges. Hinge replacement on a standard driveway swing gate typically runs $180 to $320 each, depending on gate weight and whether we need to re-weld the swing post. Post replacement runs $400 to $800 per post, including the new steel post, concrete, and re-hanging. Rail repair lands between $250 and $500, depending on the length of the damaged section. Custom welding jobs are priced by material and time: most run $150 to $400, with an hourly welding rate around $95 to $120. Latch and lock replacement falls between $120 and $240 including parts. A full roller set replacement on a slide gate usually runs $160 to $280.
What affects the price: gate weight, steel thickness, access to the failed area, and whether the concrete footing needs re-coring. What doesn’t change: you get a written price before the torch lights, and that’s the price you pay. No one adds a “discovery” line item after the fact. If another company has already quoted the job, bring the written estimate and we’ll review it at no charge.
For gate parts and welding in nearby Reseda, see our Gate Parts & Welding in Reseda page, and for Encino, visit Gate Parts & Welding in Encino. If you’re reading this from anywhere in Tarzana and want the exact number, call (424) 258-8818 for a free estimate.
Gate Parts & Welding Near Tarzana - Our Service Area
We run Encino Gate Parts & Welding calls and service throughout Tarzana and the surrounding San Fernando Valley. That includes Canoga Park, Northridge, West Hills, Sherman Oaks, Van Nuys, Chatsworth, Studio City, North Hollywood, and San Fernando. Most repair calls in Tarzana get same-day dispatch, and our trucks carry the steel, hinges, bolts, and welding equipment for nearly every common gate repair. A live person answers the phone 24 hours a day, seven days a week.
Serving Tarzana, CA - Our Local Coverage Area
We’re based in the Tarzana area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Parts & Welding in Tarzana
Gate parts and welding is the structural repair side of gate work: replacing broken hinges, resetting leaning posts, repairing bent or broken rails, welding cracked steel, swapping worn rollers, and replacing failed latches and locks. It’s the metal work that keeps the gate square, quiet, and safe. Our Gate Parts & Welding in Tarzana page covers the full scope of work.
Most hinge replacements, roller swaps, and latch repairs in Tarzana are finished in one to three hours. Post replacement takes longer because the concrete footing needs to set before the gate is re-hung, which we schedule for a return trip the following day. Rail repairs and custom welding typically run two to four hours depending on the length of the damaged section.
Gate parts and welding in Tarzana typically runs $120 to $800, depending on the repair. A latch replacement sits at the low end around $120 to $240, hinge replacement runs $180 to $320, and a full post replacement with new concrete runs $400 to $800. Every job gets a written price before work starts, so you know the exact number before you commit. Call (424) 258-8818 for a free estimate.
Yes. We work on LiftMaster, DoorKing, Elite, and Mighty Mule gate operators throughout Tarzana, and we keep the common bracket hardware and OEM parts on the truck. The welding and parts discipline is the same regardless of brand: cut out the failure, weld in sound metal, dress the weld, and photograph the record. We don’t steer you toward a replacement when a repair is the right call.
We run same-day service in Tarzana and the surrounding Valley for jobs where a gate has dropped, a post has snapped, or a weld has sheared and the gate won’t close. A live person answers the phone 24/7 at (424) 258-8818, and the technician is dispatched with a name and photo before arrival. If the gate is hanging unsafely, we prioritize the call.
All completed gate parts and welding work carries the 365-Day Done Right Promise. If the repair is not right within one full year, Vance Gate Repair makes it right at no additional charge. No argument, no fee, no expiration within that window. The written record from every job documents what was installed, so a warranty claim is straightforward.
Clear the area around the gate on both sides so the technician has room to work, and move any vehicles that block access to the gate posts and rail. If you have a written estimate from another company, have it ready for the free second-opinion review. The technician handles the rest: diagnostic photos, written price, repair, and the photo record at closeout.
Schedule Your Gate Parts & Welding Service in Tarzana Today
A sagging gate, a cracked weld, a post that’s leaning: these don’t fix themselves, and every week of delay makes the repair larger. Call (424) 258-8818 and a live person answers, day or night. You get a written price before any work begins, a photo record when the job is done, and a full year of coverage on the repair. No obligation, no pressure, just a straight number and a square gate.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Tarzana and the San Fernando Valley since 2014.